SECTION 6-B 1956 BUICK REAR AXLE SERVICE PROCEDURES 6-4 REMOVAL AND INSTALLATION OF 1956 BUICK REAR AXLE ASSEMBLY It is not necessary to remove the 1956 Buick rear axle assembly for repair or replacement of a strut rod, an axle shaft, a wheel bearing, or a wheel bearing seal; however, the 1956 Buick rear axle [...]
SECTION 5-C 1956 BUICK DYNAFLOW REMOVAL AND INSTALLATION, DISASSEMBLY AND ASSEMBLY 5-13 REMOVAL AND INSTALLATION OF 1956 BUICK DYNAFLOW TRANSMISSION Removal of 1956 Buick Dynaflow Transmission Hoist front and rear of car and rest it solidly on stands placed under frame. Frame side rail should be at least 20" above floor. Disconnect torque tube from [...]
SECTION 11-A 1955 BUICK RADIO 11 -1 1955 BUICK RADIO DESCRIPTION AND OPERATING INSTRUCTIONS Description The 1955 Buick radio installation consists of a receiver set with built in speaker mounted at the center of the instrument panel, and a sectional antenna mounted on left front fender, and suppression parts installed at various locations to eliminate interference. [...]
SECTION 5-C 1955 BUICK DYNAFLOW TRANSMISSION REMOVAL AND INSTALLATION, DISASSEMBLY AND ASSEMBLY 5-13 1955 BUICK DYNAFLOW REMOVAL AND INSTALLATION Removal of 1955 Buick Dynaflow Transmission Hoist front and rear of car and rest it solidly on stands placed under frame. Frame side rail should be at least 20" above floor. Disconnect torque tube from torque ball [...]
SECTION 11-A 1954 BUICK RADIO 11-1 1954 BUICK RADIO DESCRIPTION AND OPERATING INSTRUCTIONS Description The 1954 Buick radio installation consists of a receiver set with built in speaker mounted at the center of the instrument panel, and a sectional antenna mounted on left front fender, and suppression parts installed at various locations to eliminate interference. The [...]
SECTION 5-C 1954 BUICK DYNAFLOW TRANSMISSION REMOVAL AND INSTALLATION, DISASSEMBLY AND ASSEMBLY 5-13 1954 BUICK DYNAFLOW REMOVAL AND INSTALLATION 1954 Buick Dynaflow Removal Hoist front and rear of car and rest it solidly on stands placed under frame. Frame side rail should be at least 20" above floor. Disconnect torque tube from torque ball and [...]
SECTION 11-B 1952 BUICK RADIO 11-6 1952 BUICK RADIO DESCRIPTION AND OPERATING INSTRUCTIONS The 1952 Buick Buick Sonomatic radio installation consists of a receiver set with built in speaker mounted at the center of the instrument panel, and a 4-section antenna mounted just above the center of windshield. Some installations may also include a separate speaker [...]
SECTION 5-C 1952 BUICK REAR AXLE REMOVAL AND DISASSEMBLY PROCEDURES 5-7 REMOVAL AND INSTALLATION OF 1952 BUICK REAR AXLE ASSEMBLY When to Remove - 1952 Buick Rear Axle Assembly The 1952 Buick rear axle assembly should be removed from the car before overhaul if there is external indication of damage to rear axle or third member housings [...]
SECTION 4-E 1952 BUICK DYNAFLOW REMOVAL AND INSTALLATION, DISASSEMBLY AND ASSEMBLY 4-27 1952 BUICK DYNAFLOW REMOVAL Raise right side of hood and remove bell housing dowel bolt located to rear of cranking motor solenoid, using a suitable offset brass drift. This bolt cannot be removed from under the car. Hoist front and rear of car [...]
SECTION 4-E 1951 BUICK DYNAFLOW REMOVAL AND INSTALLATION, DISASSEMBLY AND ASSEMBLY 4-27 REMOVAL OF 1951 BUICK DYNAFLOW TRANSMISSION Raise right side of hood and remove bell housing dowel bolt located to rear of cranking motor solenoid, using a suitable offset brass drift. This bolt cannot be removed from under the car. Hoist front and rear [...]