Home » Clutch » Page 2
2014 2014/11

1955 Buick Dynaflow Removal and Installation

By |Categories: 1955, 1955 Buick Shop Manual, Literature|Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , |0 Comments

SECTION 5-C 1955 BUICK DYNAFLOW TRANSMISSION REMOVAL AND INSTALLATION, DISASSEMBLY AND ASSEMBLY 5-13 1955 BUICK DYNAFLOW REMOVAL AND INSTALLATION Removal of 1955 Buick Dynaflow Transmission Hoist front and rear of car and rest it solidly on stands placed under frame. Frame side rail should be at least 20" above floor. Disconnect torque tube from torque ball [...]

2014 2014/11

1955 Buick Dynaflow Transmission Specifications

By |Categories: 1955, 1955 Buick Shop Manual, Literature|Tags: , , , , , , , , , , , , , , , , , , , , , , , |0 Comments

SECTION 5-A 1955 BUICK DYNAFLOW SPECIFICATIONS, DESCRIPTION AND OPERATION 5-1 1955 BUICK DYNAFLOW GENERAL SPECIFICATIONS 1955 Buick Dynaflow Transmission Identification Number A production identification number is stamped into the lower edge of the reaction shaft flange directly to rear of the high (left) accumulator. The identification number consists of a letter followed by a number. See [...]

2014 2014/11

1955 Buick Clutch – Special, Super and Century Series

By |Categories: 1955, 1955 Buick Shop Manual, Literature|Tags: , , , , , , , , , , , |0 Comments

SECTION 4-A 1955 BUICK CLUTCH - SERIES 40-50-60 4-1 1955 BUICK CLUTCH SPECIFICATIONS Tightening Specifications 1955 Buick Clutch Tightening Specifications 1955 Buick Clutch Specifications 1955 Buick Clutch Specifications 1955 Buick Clutch Specification   4-2 DESCRIPTION OF 1955 BUICK CLUTCH Single plate, dry disc clutches of two different designs are used [...]

2014 2014/11

1954 Buick Dynaflow Removal and Installation

By |Categories: 1954, 1954 Buick Shop Manual, Literature|Tags: , , , , , , , , , , , , , , , , , , , , , , |0 Comments

SECTION 5-C 1954 BUICK DYNAFLOW TRANSMISSION REMOVAL AND INSTALLATION, DISASSEMBLY AND ASSEMBLY 5-13 1954 BUICK DYNAFLOW REMOVAL AND INSTALLATION 1954 Buick Dynaflow Removal Hoist front and rear of car and rest it solidly on stands placed under frame. Frame side rail should be at least 20" above floor. Disconnect torque tube from torque ball and [...]

2014 2014/11

1954 Buick Dynaflow Transmission Specifications

By |Categories: 1954, 1954 Buick Shop Manual, Literature|Tags: , , , , , , , , , , , , , , , , , , , , , , |0 Comments

SECTION 5-A 1954 BUICK DYNAFLOW SPECIFICATIONS, DESCRIPTION AND OPERATION 5-1 1954 BUICK DYNAFLOW TRANSMISSION SPECIFICATIONS 1954 Buick Dynaflow Transmission Identification Number A production identification number is stamped into the lower edge of the reaction shaft flange directly to rear of the high (left) accumulator. The identification number consists of a letter followed by a number. See figure [...]

2014 2014/11

1954 Buick Clutch – Special, Super and Century Series

By |Categories: 1954, 1954 Buick Shop Manual, Literature|Tags: , , , , , , , , , , |0 Comments

GROUP 4 - 1954 BUICK CLUTCH, S-M TRANSMISSION, UNIVERSAL JOINT 4-1 1954 BUICK CLUTCH SPECIFICATIONS Tightening Specifications 1954 Buick Clutch Tightening Specifications 1954 Buick Clutch Specifications 1954 Buick Clutch Specifications 1954 Buick Clutch Specification   4-2 DESCRIPTION OF 1954 BUICK CLUTCH Single plate, dry disc clutches of two different designs [...]

2014 2014/11

1952 Buick Dynaflow Removal and Installation

By |Categories: 1952, 1952 Buick Shop Manual, Literature|Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , |0 Comments

SECTION 4-E 1952 BUICK DYNAFLOW REMOVAL AND INSTALLATION, DISASSEMBLY AND ASSEMBLY 4-27 1952 BUICK DYNAFLOW REMOVAL Raise right side of hood and remove bell housing dowel bolt located to rear of cranking motor solenoid, using a suitable offset brass drift. This bolt cannot be removed from under the car. Hoist front and rear of car [...]

2014 2014/11

1952 Buick Dynaflow Transmission

By |Categories: 1952, 1952 Buick Shop Manual, Literature|Tags: , , , , , , , , , , , , , , , , , , , , |0 Comments

SECTION 4-C 1952 BUICK DYNAFLOW SPECIFICATIONS, DESCRIPTION, AND OPERATION 4-15 1952 BUICK DYNAFLOW GENERAL SPECIFICATIONS 1952 Buick Dynaflow Transmission Identification Number A production identification number is stamped into the lower edge of the reaction shaft flange directly to rear of the high (left) accumulator. The identification number consists of a letter followed by a number. See [...]

2014 2014/11

1952 Buick Clutch – Special and Super Series

By |Categories: 1952, 1952 Buick Shop Manual, Literature|Tags: , , , , , , , , |0 Comments

SECTION 4-A 1952 BUICK CLUTCH-SERIES 40-50 4-1 1952 BUICK CLUTCH SPECIFICATIONS Tightening Specifications 1952 Buick Clutch Tightening Specifications 1952 Buick Clutch Specifications 1952 Buick Clutch Specifications 1952 Buick Clutch Specification   4-2 DESCRIPTION OF 1952 BUICK CLUTCH 1952 Buick Clutch Assembly The single plate, dry disc clutch used in Series 40-50 [...]

2014 2014/11

1953 Buick Clutch, Transmission, Universal Joint

By |Categories: 1953, 1953 Buick Shop Manual, Literature|Tags: , , , , , , , , , , , , , , , , , , |0 Comments

GROUP 4 - 1953 BUICK CLUTCH, TRANSMISSION, UNIVERSAL JOINT NOTE: For 1953 Buick clutch and transmission information not listed above refer to Group 4 of the 1952 Buick Shop Manual. 4-1 1953 BUICK CLUTCH AND TRANSMISSION TYPES A synchromesh transmission and single plate clutch are standard equipment on Series 40 and 50, and the Dynaflow transmission [...]

By continuing to use the site, you agree to our privacy policy and the use of cookies. More Information

The cookie settings on this website are set to "allow cookies" to give you the best browsing experience possible. If you continue to use this website without changing your cookie settings or you click "Accept" below then you are consenting to this.

Close